Plus Series Dual Voltage Isolated Power Panel - Model IPD-P
The Plus Series Dual Voltage Isolated Power Panel (Model IPD-P) provides both low and high volt output requiring only one feed using one primary transformer and two secondary transformers. This allows users to have high volt output (208V, 220V, or 240V) to power laser equipment without requiring an additional power feed.
Included with Plus Series Dual Voltage Isolated Power Panel
- Dual secondary winding isolation transformer for supplying 208V, 220V, or 240V circuits
- Up to 16 120V, 20A circuits with standard-line powered equipment
- Up to 2 208V, 220V, or 240V, 30 or 50A dedicated circuits for laser-powered
- The unit is housed in a single panel and fed from a single primary source
Panel Sizing
|
kVA Size |
kVA Size |
Back Box Size |
Max Weight |
| 5 |
7.5 10 |
70"H x 36"W x 12"D | 550 |
| 7.5 | |||
| 10 | 15 | 665 |
Select from available combinations for high and low voltages (e.g., 7.5kVA at 120V low side and 10kVA at 208V high side).
- The kVA of the panel transformer is determined by adding together the kVA of the low volt section (120V) and the high volt section (208 - 240V). (Example: If 7.5 kVA is required for the low volt section and 15 kVA is required for the high volt section, the overall size is 22.5 kVA.)
Features
All Plus Series Model IPD-P Isolated Power Panels include:
Hospital Grade Isolation Transformer:
- Standard sizes for each section range from 5 to 15kVA or up to a combined maximum
of 25kVA - Primary voltages: 480, 277, 240, 208, and 120 VAC
- Secondary voltages: 240, 208, and 120 VAC
- Low leakage, electrostatically shielded primary and secondary windings
- 220°C Class R Insulation
- Top mounted, clamped and bolted design with anti-vibration mounting bushings for quiet operation
- Designed and built in accordance with UL and CSA Standards
- 50Hz available (optional)
Interior Chassis:
- Interior chassis built to order, fully designed and assembled in the factory, and 100% tested
- Adjustable electronic trip options are available for achieving 0.1 seconds of system coordination
- Primary main circuit breaker
- Secondary main circuit breaker for low (120V) side
- Up to 16 factory installed 120V, two-pole, bolt-on branch circuit breakers
- High volt section breakers are determined by kVA size of the panel
- Copper bus panelboard interior
- Terminal strip for connecting Remote Annunciator(s)
- Customer may specify standard circuit breakers from Eaton, GE, Siemens, or Schneider Electric for consistent coordination or to maintain facility standard
SafeDetec® Line Isolation Monitor (LIM):
- Industry's newest Line Isolation Monitor technology, providing advanced warning of faults to help reduce downtime and increase operational efficiencies
- Advanced filtering and noise suppression for improved accuracy and reliability
- High contrast 40-character LED display for better visibility and viewing angle
- Universal 120-240 VAC power input allows LIMs to be directly Interchanged from 120V to 208V/240V laser panels without changing the internal jumper or switch settings
- Additional parameters can be displayed on the user interface for more advanced troubleshooting, such as L1 and L2 line-to-ground voltages, insulation resistance, and insulation capacitance
- Increased memory allows more log entries and a longer history of LIM data
Enclosure and Trim:
- Heavy-duty galvanized steel back box designed for flush mounting; can be shipped ahead of interior during rough-in
- Stainless steel front trim panel with fully hidden hinged, door-in-door construction reduces damage and potential injuries during installation, testing, and maintenance
- Surface mounting options available
Available Accessory Outlet:
- If a laser or laser outlet is needed, use Model LO Laser Outlet
- LO Outlet Module includes user-specified NEMA receptacle, galvanized back box, and a stainless steel front trim with hinged door.
Installation
- If the Isolated Power Panel is not installed inside the patient/procedure room, National Electric Code requires that a Remote Annunciator be installed so that it is “conspicuously visible” in the area served.
- Special low leakage wire should always be used for the powered conductors of branch circuit wiring. XPLE type insulation such as XHHW-2 wire is recommended with a dielectric constant of less than 3.5. Standard type insulation such as THHN is appropriate for the incoming primary and the ground wires only.
- The NEC (Article 517.160) requires secondary circuits to be colored brown and orange, with a distinctive stripe in a contrasting color. The brown wire is connected to the L2 bus and the hot side (brass screw) of a standard NEMA receptacle. The orange wire, L1 is connected to the silver screw where neutral would be connected. Polarity should be maintained throughout the installation.
- Conduit runs for branch circuits should be as short and direct as possible to minimize accumulated leakage current in the circuit conductors. Generally, 400‐450 feet is the maximum recommended cumulative length of all branch conductors from a single transformer. Avoid unnecessary bends and junctions. Select for more information.
- Do not use pulling compounds to lubricate inside of the conduit. This will break down the insulation properties and raise leakage current. A dry talc powder may be used. It is typical to use conduit with a slightly larger diameter to ease pulling and avoid damage to wire insulation. An interior coating of PVC may also be used.
- Isolated power circuits must be kept separate from other circuits. Do not share the conduit or raceway with non‐isolated circuits, or isolated circuits from another system.
- Each receptacle and equipment grounding connector must be connected back to Reference Ground Bus inside Isolation Panel to maintain Equipotential grounding system. If multiple panels serve the same space, they must be bonded together.
Technical Drawings
- Plus Series Model IPD-P Technical Drawing
- Plus Series Model IPD-P Technical Drawing with Additional Options
Product Downloads
- Plus Series Model Numbering Guide
- Plus Series Isolated Power Specifications
- Plus Series Isolated Power Systems Installation and Operation Manual
- Isolated Power Product Catalog
Certifications
PG LifeLink Plus Series Dual Voltage Isolated Power Panel is designed, built, and tested in accordance with the following:
CSA Certification
CSA C22.1 Part 1, and CSA C22.2 No. 204
HCAI (California Department of Health Care Access and Information)
OSP-0210-10
*Only PG LifeLink offers this as standard